DIY Tool Organization + Storage

By Love and Renovations
img_5203
img_5208
Kreg Academy Kreg Academy

How to build a simple but super functional storage solution for your tools! This little organization workhorse holds more than you'd ever expect, and keeps your garage organized.

Difficulty moderate

Tools

Kreg Tools

Other Tools

  • Table Saw
    Table Saw
  • Tape Measure
    Tape Measure
  • Clamps
    Clamps
  • Drill (cordless)
    Drill (cordless)
  • Nail Gun
    Nail Gun

Materials

Wood Products

  • 1 Plywood , 3/4" Thick , Full Sheet

Hardware & Supplies

  • 32 Pocket Hole Screws
  • 12 1 1/4" screws
  • 20 18-gauge nails
See All Tools & Materials

Cut List & Parts

  • 4 Box pieces , 20.25”X16”
  • 4 Box pieces , 10.5” x 16”
  • 2 Box shelves , 9 1/8 " x 16"
  • 2 Shelves , 18" x 16"
  • 4 Drill supports , 4" x 8"
  • 4 Drill supports , 2.25" x 8"
  • 2 Side drill supports , 3/4" x 8"
  • 1 Backing , 19" x 21.5"
See Full Cut List & Parts

Directions

  • Cut Plywood according to cut list

    Start by cutting down your plywood according to the cut list. Feel free to adjust the sizing depending on what you need for your space.

    Step 1

  • Assemble Side Boxes

    Using two 20.25X16 and two 10.5X16 pieces per box, assemble two boxes using pocket holes and wood glue.

    I recommend using corner clamps to help you ensure the boxes are square as you assemble.

    Step 2

  • Assemble Drill Hangers

    Assemble your drill hangers by drilling one 2.25"x8" piece into the bottom of a 4"x8" piece. Be sure to pre-drill 2-3 holes in the smaller piece before drilling.

    Step 3

  • Mark spots on shelf for drill hange

    Mark lines on one of the 18"x16" shelves where the drill hangers will go. From center-to-center, the spacing between each drill hanger should be 3.75". The spacing between the side boxes and the first drill hanger on each side should be 3 3/8".

    After marking the spots, pre-drill the holes for the drill hangers. You will not hang them until after attaching the shelf.

    Step 4

  • Drill pocket holes in the shelves

    Drill pocket holes on the short sides of each 18" x 16" shelf.

    Step 5

  • Attach top shelf

    Attach the top shelf to the two boxes using wood glue and pocket screws. It should be attached 3" from the top of the boxes.

    Step 6

  • Attach second shelf

    Attach the second shelf in the same manner - it should be 10" from the first shelf.

  • Attach drill hangers to shelf

    Add wood glue, then the drill hangers into the pre-drilled holes on the bottom shelf.

    Step 8

  • Add shelf pieces to the boxes

    Drill pocket holes in the two 9 1/8" x 16" pieces (NOTE: I highly recommend assembling your boxes prior to cutting these pieces, then measuring and cutting based on your box, to account for any variations).

    Using wood glue and pocket holes, add a shelf in each box, approximately 13" from the bottom of the shelf (this is obviously an optional step - if you prefer to store taller tools in this space, leave it open).

  • Attach side pieces for drill hanger

    Using wood glue and screws, attach the two 3/4" x 8" pieces to each box, approximately 2" from the bottom of the box and set back 1/2". (Be sure to pre-drill the holes to avoid splitting the wood)

  • Attach backing

    Using wood glue and a nail gun, attach the 19" x 21.5" piece to the back of your organizer.

    Step 11

  • Paint and hang

    Paint in your desired color and hang it up on your garage wall - then, fill it up with all of your favorite tools!

    Step 12