Sand & Water Play Table

By Jen Woodhouse
kreg-sand-table
kreg-sand-table2
sand-table01
sand-and-water-table
sand-water-play-table2
Kreg Academy Kreg Academy

Your kids will love playing with this sand and water table. Complete with a chalkboard lid, the possibilities for imaginative play are endless! This sand and water table accommodates two store-bought 28-quart tubs and the hinged lid covers the sand and water when not in use.

Difficulty moderate

Tools

Kreg Tools

Other Tools

  • Circular Saw (corded)
    Circular Saw (corded)
  • Tape Measure
    Tape Measure
  • Drill (cordless)
    Drill (cordless)
  • Nail Gun
    Nail Gun
  • Sander
    Sander

Materials

Wood Products

  • 2 Board , 1x8 , 96"
  • 1 Board , 1x6 , 24"
  • 4 Board , 1x3 , 96"
  • 7 Board , 1x2 , 96"
  • 1 Plywood , 1/2" Thick , Full Sheet

Hardware & Supplies

  • 2 Torsion Hinges
  • 1 1-1/4" Kreg Blue-Kote Pocket Hole Screws
  • 1 1-1/4" Exterior Wood Screws
  • 1 1-1/4" Brad Nails
  • 1 Chalkboard Paint
  • 1 Exterior-Grade Finish
See All Tools & Materials

Cut List & Parts

  • 2 Box Sides , 3/4" x 7-1/4" x 18-3/4"
  • 2 Box Sides , 3/4" x 7-1/4" x 47-3/4"
  • 9 Slats , 3/4" x 1-1/2" x 17-1/4"
  • 1 Divider , 3/4" x 5-1/2" x 17-1/4"
  • 8 Legs , 3/4" x 2-1/2" x 22-3/4"
  • 2 Shelf Rails , 3/4" x 2-1/2" x 49-1/4"
  • 17 Shelf Slats , 3/4" x 1-1/2" x 13-3/4"
  • 1 Top , 1/2" x 50-3/4" x 20-1/4"
  • 2 Trim , 3/4" x 1-1/2" x 50-3/4"
  • 2 Trim , 3/4" x 1-1/2" x 17-1/4"
See Full Cut List & Parts

Directions

  • Build the Box

    Drill 3/4" pocket holes as shown and construct the box with 1-1/4" pocket hole screws and wood glue.

    Step 1

  • Add the Slats

    Drill 3/4" pocket holes into the 1x2 support slats and attach to the box with 1-1/4" pocket hole screws and wood glue. Space the slats approximately 4-1/4" apart.

    Step 2

  • Attach the Divider

    Drill 3/4" pocket holes into 1x6 divider and attach as shown with 1-1/4" pocket hole screws and wood glue.

    Step 3

  • Add the Legs

    Pre-drill pilot holes and drive 1-1/4" wood screws to attach the legs to the box as shown.

    Step 4

  • Construct the Bottom Shelf

    Drill 3/4" pocket holes and construct the bottom shelf as shown with 1-1/4" pocket hole screws and wood glue. Space slats approximately 1-1/2" apart.

    Step 5

  • Attach the Bottom Shelf

    Attach the bottom shelf with 1-1/4" pocket hole screws. The bottom shelf is 2" from the ground.

    Step 6

  • Attach the Top

    Install hinges to attach the top to the play table. Note: torsion hinges are recommended to keep the lid from slamming down on tiny fingers.

    Step 7

  • Add Trim

    Attach 1x2 trim to the top with 1-1/4" brad nails and wood glue.

    Step 8

  • Visit JenWoodhouse.com

    For more DIY project ideas and free building plans, please visit JenWoodhouse.com

    Step 9

  • Sand, Stain/Paint, and Finish

    Sand, stain or paint, and finish with an exterior-grade top coat as desired. Because plywood is not suitable for outdoor use, I recommend storing the play table in a garage or under a covered area when not in use to protect it from outdoor elements.

    Step 10